Alien Reproduction Vehicle

spacecase0

earth human
So one of these can generate a quadrature signal, e.g. CH1=sine, CH2=cosine?



I've looked into using high-speed power OP-amps (not IC's). They're pricey, though. Will such beasts work? My analog skills suck.
I am way better at analog than digital

an arbitrary wave form generator will make whatever you want.
the ones I have can be linked together, so I can make 4 phase power if I want (why I bought them)
I am only using one of them for this test setup
it has some internal sync that you can then set a phase angle from,
so you can set sine wave on the first channel and then set 90 degree (or any number you like) delay for the second channel
it has very good defaults for waveshape types, and there are lots of them.
if you plug it into a computer, you can literately draw any wave you want and upload it.
it has 100mA out and adjustable DC bias, so you could drive a mosfet directly off it if you wanted to (I would not do this without additional protection circuits as mosfets tend to fry in experiments, and they conduct back main power into what use to be the gate, frying whatever is connected )

some fancy OP-amps have built in protections so they don't break easy, got a part number for what you are thinking about ?
 

spacecase0

earth human
What browser do you use?...This site should work for any browser...
they want scripts and things like that running.
I don't let my web browser talk to my hard drive files.
and none of the sites let you FTP or SSH in (like I did when I ran a web server), or at least not that I know of.
I can email a picture pretty easy because all that is on my phone.
like I said, I could try harder.
 

nivek

As Above So Below
they want scripts and things like that running.
I don't let my web browser talk to my hard drive files.
and none of the sites let you FTP or SSH in (like I did when I ran a web server), or at least not that I know of.
I can email a picture pretty easy because all that is on my phone.
like I said, I could try harder.

If I know what your browser requires to connect this site I can change a few settings to allow it...
 

nivek

As Above So Below
I would love to be able to upload pictures here, first thing I did was try it here, but it was upload by URL only.

Let me know by pm or something if you prefer, the requirements and I'll set it up for you in this end...
 
I am way better at analog than digital

an arbitrary wave form generator will make whatever you want.
the ones I have can be linked together, so I can make 4 phase power if I want (why I bought them)
I am only using one of them for this test setup
it has some internal sync that you can then set a phase angle from,
so you can set sine wave on the first channel and then set 90 degree (or any number you like) delay for the second channel
it has very good defaults for waveshape types, and there are lots of them.
if you plug it into a computer, you can literately draw any wave you want and upload it.
it has 100mA out and adjustable DC bias, so you could drive a mosfet directly off it if you wanted to (I would not do this without additional protection circuits as mosfets tend to fry in experiments, and they conduct back main power into what use to be the gate, frying whatever is connected )

some fancy OP-amps have built in protections so they don't break easy, got a part number for what you are thinking about ?

look here
 

spacecase0

earth human
they are, 400KHz, 300KHz, and 500KHz and still have power out
is that fast enough for you ?

it is going to be lots lower price to use a mosfet, and they will be much faster. but it will be a bit of building.
how about the IRFP250N ? IRFP250NPBF Infineon Technologies | Discrete Semiconductor Products | DigiKey
they are only $2.65 each, and you would need 4 of them,
and it would be way faster than where thinking of.

something like this goes up to 70MHz
IXZ2210N50L2 IXYS-RF | Discrete Semiconductor Products | DigiKey
you would likely need 4 of them as well, (2 channels set up as a push pull (if that is what it is called))

edit:
look at this schematic,
http://chemelec.com/Projects/Inverter-2/Mosfet-Sch-2.png
see how they did the mosfet output into the transformer ?
that would likely be the easiest way to do it, you would need 2 times the copper coils (one for each polarity), but then you don't have the complexity on the circuitry side.
 
Last edited:

humanoidlord

ce3 researcher
if you have a steel hull, it will help the effect because of the steel magnifying the effect of the coils (like any transformer core). and if you make the hull parts electrically connected, it will get induction heating, but if you laminate it like you do in a transformer core, or just insulate panels from each other, you will not get to much heating.
once you get past the magnetic saturation point, or spin the field to fast, the steel is not going to help you at all.
wilbert smith said the part of the wrecked craft that he knew of was made out of a magnesium ferrite, not quite sure what that means though (replace the iron with magnesium ? or add magnesium to ferrite ?)
----------------------------
so, I tested the MAGVID idea slightly better than last time, only had rare earth magnets, and at that they were not sticking out past the coils either...
need to wind an electromagnet for the center coil, but have not made it to a hardware store yet.
either way, I am running somewhere less than 100W, 40KHZ, ~19inch dia., ~11 tall
started to smell ozone after it ran about 30 seconds. and it was not coming form the power supply, amplifiers, or any other of the electronics. can't run it at high power to long or my amplifier heats up.
so it does seem to do something, maybe...
it did not mess with a watch ticking off time (checked to 0.1 seconds after 5 min. run time)
does not mess with the binding strength meter at all
should be pretty easy for me to double my power in to it, will try to get to that today.
hmm pretty interesting, so the MAGVID does something after all, i am a bit skeptic on the levitation claims for now
 

humanoidlord

ce3 researcher
It is my opinion that many of those plasmoids/orbs might be living entities. Just look at the footage from the space shuttle missions where a number of spherical object move about outside the shuttle. Literal swarms of them, and they're translucent too.
Maybe it's hard for people to accept that life could exist in the earth's upper atmosphere, because most UFO buffs refer to them as space craft. David Wilcock has written about these life forms, e.g. in Divine Cosmos. There's also an interesting discussion about so-called vacuum domains and conciousness units in some of his other free online books. Actually, it's these early texts that got me listening to the guy, although this Corey Goode thing is a little depressing...
thats something i always considered, ball lightining is a life form, a interdimensional one, just like the humanoids but more mundane
 

spacecase0

earth human
I have an update,
I brought over someone that is pretty psychic to see if they could detect anything about the MAGVID device while running, they detected nothing, but that is not why I post this.
and this time, it is not make the ozone smell (and my amplifier got hot way faster)
tried it again just now, and still no ozone. so I am not sure what to think now.

I bet it just needs lots more power in.
pretty sure I have at least four MG300Q1US41 (an IGBT, 1200V, 300A, 2KW, about 650KHz limit)
now I know that is not that high of frequency (and would likely never try past 300KHZ with it), but I do have my doubts for pushing radio frequencies into large coils that are many times the wavelength of the radio waves
so maybe solving it on the power side will do it
someone posted this on the other forum in that ARV thread
Saucer Propulsion
so we are not the only ones to be trying to figure out the ARV,
if the reports are correct, the switching frequency might be something that people can here, maybe 15KHz to 20 KHz but that could also easily be the switching frequency for the capacitors.

I have mixed thoughts on if it will levitate or not, (it is symmetrical, so what way would the thrust be ?)
but there is a very good change it will reduce inertial mass so that some other method can move it easy.
 
I bet it just needs lots more power in.
pretty sure I have at least four MG300Q1US41 (an IGBT, 1200V, 300A, 2KW, about 650KHz limit)
now I know that is not that high of frequency (and would likely never try past 300KHZ with it), but I do have my doubts for pushing radio frequencies into large coils that are many times the wavelength of the radio waves
so maybe solving it on the power side will do it
someone posted this on the other forum in that ARV thread
Saucer Propulsion
so we are not the only ones to be trying to figure out the ARV,
if the reports are correct, the switching frequency might be something that people can here, maybe 15KHz to 20 KHz but that could also easily be the switching frequency for the capacitors.
It was Vencislav Bujić that suggested that the outer "tip" of the virtual bar magnet should
reach c for some reason, e.g. FTL travel. As you notice, increasing power to the coils will
cause the virtual bar magnet to "lengthen" and reach farther out before it fades at the "tip", and with
a larger circumference that the "tip" sweeps over, the easier it is to get the high velocity of this "tip",
maybe even up to (or near) c.

Another way to get smaller coils (=higher frequency) and lower impedance is to have more than four coils. We could hook up
a whole bunch of those function generators to feed e.g. 6, 8, 12, or 16 coils! An advantage with more than four coils is safety: if one oscillator/amplifier gets fried, the adjacent coils could compensate for that by increasing their power, and the BTV/bubble/electron sheet will (hopefully) be intact.

Musing again: my earlier wild hypothesis, that the Repulsin's BTV/bubble/electron sheet will become self-sustaining at a high enough energy level (=highest possible speed of the air recirculating in/around the device), maybe this also applies to the MAGVID!!?? That means that after we've created it, the Universe will uphold the BTV/bubble/electron sheet by itself indefinitely! The MAGVID coils could then be used to shut down the self-sustaining BTV/bubble/electron sheet by running it "backwards" when you want to come to a standstill (if such a thing exists in interstellar space—standing still in relation to what ? :) )
I have mixed thoughts on if it will levitate or not, (it is symmetrical, so what way would the thrust be ?)
but there is a very good change it will reduce inertial mass so that some other method can move it easy.

Wow! Never thought of that! I always surmised that the gravitator was used to:
  1. distort the BTV/bubble/electron sheet for directional control when the MAGVID is active, and/or
  2. hover the craft when parked.
That means that maybe the gravitator — in addition to (at least one of) the above points — could be what propels the craft, maybe even in FTL flight! The BTV/bubble/electron sheet just acts as a gravity shield rendering the craft and its occupants "mass-less", but with working bodily functions since no natural laws are broken inside the BTV/bubble/electron sheet. McCandlish is dead wrong in his mass cancellation assumption (and now I've read 75% of the Energetic Forum thread).
 

spacecase0

earth human
been thinking about other ways to test the MAGVID device
if we are really going for the speed of light at the point of the coils,
the coils can only be one turn (for it to be at all practical).
they would have to be resonant like an antenna
so if you built 4 one wavelength square loop antennas and then made them into a circle, you would be just at the speed of light where the coils are.
the wiring setup would be opposite loop is wired in series (I would use one electrical wavelength of coax cable to get the signal to the other side, and then connect one set of coils with a 1/4 wave coax cable delay loop.
and wire each set (the one with the delay and the one without the delay) in parallel to your power feed line.
that would get you close enough to 50 ohms that most radios transmit with.
seems to me that the 6M band is the highest frequency that you can still use an antenna tuner with (to fix any impedance mismatch from not perfect building, and not having 100 ohm coax for the delay line (use 75 ohm)), and it is about the correct size to test anyway with an outside circumference of about 18 foot
clearly it would only work with one frequency, but I guess that is ok. and if you are not following the logic, the frequency and size here are going to change together as you choose various frequencies, so I am not to sure it matters to much what frequency you choose.
the real question is that I have no clue what polarization you would choose, but there are just not that many choices, vertical, horizontal, or maybe 45degrees would get you something useful, so I guess it can just be changed to see what works.
the reason of all this is that powerful radio transmitters are pretty easy to get (or at least easy to borrow, just tell someone you want to test a new antenna design at high power)

edit:
I am trying to make this as easy as I can for everyone to follow, but I get that it may be hard to follow without a schematic, if anyone does not follow, please tell me and I will try to do better.
 
Last edited:

spacecase0

earth human
It was Vencislav Bujić that suggested that the outer "tip" of the virtual bar magnet should
reach c for some reason, e.g. FTL travel. As you notice, increasing power to the coils will
cause the virtual bar magnet to "lengthen" and reach farther out before it fades at the "tip", and with
a larger circumference that the "tip" sweeps over, the easier it is to get the high velocity of this "tip",
maybe even up to (or near) c.

Another way to get smaller coils (=higher frequency) and lower impedance is to have more than four coils. We could hook up
a whole bunch of those function generators to feed e.g. 6, 8, 12, or 16 coils! An advantage with more than four coils is safety: if one oscillator/amplifier gets fried, the adjacent coils could compensate for that by increasing their power, and the BTV/bubble/electron sheet will (hopefully) be intact.

Musing again: my earlier wild hypothesis, that the Repulsin's BTV/bubble/electron sheet will become self-sustaining at a high enough energy level (=highest possible speed of the air recirculating in/around the device), maybe this also applies to the MAGVID!!?? That means that after we've created it, the Universe will uphold the BTV/bubble/electron sheet by itself indefinitely! The MAGVID coils could then be used to shut down the self-sustaining BTV/bubble/electron sheet by running it "backwards" when you want to come to a standstill (if such a thing exists in interstellar space—standing still in relation to what ? :) )


Wow! Never thought of that! I always surmised that the gravitator was used to:
  1. distort the BTV/bubble/electron sheet for directional control when the MAGVID is active, and/or
  2. hover the craft when parked.
That means that maybe the gravitator — in addition to (at least one of) the above points — could be what propels the craft, maybe even in FTL flight! The BTV/bubble/electron sheet just acts as a gravity shield rendering the craft and its occupants "mass-less", but with working bodily functions since no natural laws are broken inside the BTV/bubble/electron sheet. McCandlish is dead wrong in his mass cancellation assumption (and now I've read 75% of the Energetic Forum thread).
pretty sure I have tried the 12 coil approach a few years ago (or at least close to it), I did set the outer coil to be the speed of light, I used pulsing DC, was a custom 6 phase power supply that I built. only about 70W out though
if you are only running at one frequency, you can run radio frequency delay lines to get whatever phase angle you want, see my previous post (we must have been typing at the same time)
 
been thinking about other ways to test the MAGVID device
if we are really going for the speed of light at the point of the coils,
the coils can only be one turn (for it to be at all practical).
With more power to the coils (and maybe more coils!), the whole virtual bar magnet will be longer and the diameter where the speed of light rotation (the "tip") occurs will be farther away from the coils radially. So, we have one fixed frequency and regulate the density/size/energy of the BTV/bubble/electron sheet with the power to the coils.

Looking at the large coil(s) around the crew compartment on McCandlish'es blue print, what frequency would you think is used?
Must be tens to hundreds of kHz's and not tens of MHz's, don't you think? And maybe there's more than four coils in there! Remember: it's only James Stephens that says so in the September 1995 "GroomLake`Colonel`Reveals`All" USENET post (reproduced here).
 

spacecase0

earth human
With more power to the coils (and maybe more coils!), the whole virtual bar magnet will be longer and the circumference where the speed of light rotation (the "tip") occurs will be farther away from the coils radially. So, we have one fixed frequency and regulate the density/size/energy of the BTV/bubble/electron sheet with the power to the coils.

Looking at the large coil(s) around the crew compartment on McCandlish'es blue print, what frequency would you think is used?
Must be tens to hundreds of kHz's and not tens of MHz's, don't you think? And maybe there's more than four coils in there! Remember: it's only James Stephens that says so in the September 1995 "GroomLake`Colonel`Reveals`All" USENET post (reproduced here).
with how large that big coil is, it sure seems like it is running direct current
if you go look at a chart like this
American Wire Gauge Chart and AWG Electrical Current Load Limits table with skin depth frequencies and wire breaking strength
the most they are running would be 410 Hz
and given how large the coil is, likely it is DC
 

spacecase0

earth human
here is another thought.
let us say that the large outer coil on the ARV is the center coil in the MAGVID method #2
and the spinning magnetic field is made by the spinning electric field in the capacitors and not magnetic coils at all
 
Top