Alien Reproduction Vehicle

I'd think about a model which is no more than 1 foot across at the most.

The smaller the MAGVID, the higher the frequency on the four coils must be. E.g. for the angular velocity at the "tip" of the virtual bar magnet to reach c, for different diameters you'd need:

1ft diameter = 300MHz
3ft diameter = 100MHz

But maybe you don't need an angular velocity near c. I heard rumors telling that Stefan Marinov's MAGVID replication started to become interesting around 40-50 kHz, although the diameter is unknown. (I still don't believe that Stefan Marinov = James Stephens.)

It's hard to tell the # of turns on the coils depicted in McCandlish'es ARV blue print.
 
BTW, don't you find it intriguing that in some artwork created by inspiration from the statements made by Gary McKinnon, the alleged cigar spacecraft USSS Hillenkoetter shows signs a MAGVID drive? OK, it shows two spherical fields here, but maybe they're more hemispherical and together form a larger spheroidal field that envelop the craft.
index.php


The infamous insider Corey Goode also present similar artwork at a conference:
index.php
 

Attachments

  • solar_warden_rev1.png
    solar_warden_rev1.png
    1.8 MB · Views: 476
  • corey-goode-points-out-torsion-fields-of-cigarshaped-spacecraft.png
    corey-goode-points-out-torsion-fields-of-cigarshaped-spacecraft.png
    1 MB · Views: 499

spacecase0

earth human
the number of turns just sets your impedance, have to match that to the amplifier you have, so I don't need number of turns from others.
I think I am going to go for a 20 foot circumference , that puts me at about 45MHz to get to c at the diameter of the coils, , I can do 75W in that frequency range. only issue is that I can only get my 90degree phasing by using a delay loop (coax cable), so that means that I will not be able to change the frequency without rewiring it. but will need to buy a few parts to set that up, they are not much and easy to get.
I can make zero to 50KHz with variable frequency and perfect phase and about 150W. and sounds like I should test that first if I might see something.
 

humanoidlord

ce3 researcher
BTW, don't you find it intriguing that in some artwork created by inspiration from the statements made by Gary McKinnon, the alleged cigar spacecraft USSS Hillenkoetter shows signs a MAGVID drive? OK, it shows two spherical fields here, but maybe they're more hemispherical and together form a larger spheroidal field that envelop the craft.
index.php


The infamous insider Corey Goode also present similar artwork at a conference:
index.php
gary probally saw traps put there to drive attention off more interesting stuff
also corey goode is the biggest liar i have ever seen
 

Gambeir

Celestial
The smaller the MAGVID, the higher the frequency on the four coils must be. E.g. for the angular velocity at the "tip" of the virtual bar magnet to reach c, for different diameters you'd need:

1ft diameter = 300MHz
3ft diameter = 100MHz

But maybe you don't need an angular velocity near c. I heard rumors telling that Stefan Marinov's MAGVID replication started to become interesting around 40-50 kHz, although the diameter is unknown. (I still don't believe that Stefan Marinov = James Stephens.)

It's hard to tell the # of turns on the coils depicted in McCandlish'es ARV blue print.

Thanks, for explaining that Mathias. As you know, the reason I originally went to energetic forums was because the specifics are not anything I have any real knowledge or experience with. I don't know anything about electronics and never will. I'll be dead before I know half of what you or Spacecase0 already know.

As you know, I've been communicating with John Iwaszko and his brother Adam on Antigravity Research.I have no training or experience of any kind dealing with electrical systems. I can tell you what it takes and why it works according to theories, and I can build anything within reason, but I need to have an instruction manual with the specifics when it comes to this area.

I will never know, nor should I even try to begin to learn what others already know, I'd be wasting my time trying to accomplish that task. That's not where my talent lies. If we don't yet have antigravity in the mainstream it's only because no one before has put the puzzle together, mainly because they have been lead astray by hucksters purposely bent on accomplishing that mission.

My expertise, such as it is, lies in law, investigative science, in research, and critical reasoning and writing. Nobody should expect me to explain how many coils of wire to put anywhere unless they have a strong desire to either electrocute themselves or else burn the house down.

For that specific reason I originally looked for assistance on another forum, but though competent people exist there in droves, none seemed able to make the associative leaps necessary to assemble the whole picture. For that reason I began searching for professional assistance and have been a quasi~advisory assistant, providing information and ideas while technically gifted experts work on actual experimental results.

In my opinion the worlds leading authority on anti~gravity technology have been doing this experimental research.

John R Iwaszko | AurumSolis Technologies - Academia.edu
AurumSolis Technologies – Inspiring Technological Innovation
AurumSolis Technologies

Here's the thing. I cannot say what I know in full until a provisional patent is filed. That's provided of course that the testing continues to be productive, which I have no doubt it will be since it's all supported by established theoretical concepts of matter and motion, but then again I don't really know anything other than the theoretical ideas say this is what should happen.

Now as for the MAGVID, this is something I have to study in more detail, and then I need to have the scientists review it an provide commentary on what they think. As of right now, I'm not sure that the MAGVID is not doing more than what you have assembled Mathias. It might be doing more but I'm not competent enough to know if what I think it might be doing is feasible.

PS: In fact it might doing a lot more but then you're already aware of that much.
Aliens: Us From A Future Time?
 
Last edited:

Gambeir

Celestial
BTW, don't you find it intriguing that in some artwork created by inspiration from the statements made by Gary McKinnon, the alleged cigar spacecraft USSS Hillenkoetter shows signs a MAGVID drive? OK, it shows two spherical fields here, but maybe they're more hemispherical and together form a larger spheroidal field that envelop the craft.
index.php


The infamous insider Corey Goode also present similar artwork at a conference:
index.php

Uh huh, and it looks ever so much like the pressure hull of a submarine doesn't it? Your tax dollars aren't going to the military of earth and haven't been going there for 70 years. We are paying for an secret civilization and have been paying for this civilization for the last 50 years or more. That's why these politicians are all crazy nut cases, they are all people whom have been chosen to fill roles to keep and illusion in place and to keep strip mining the people of money and resources.
 
Uh huh, and it looks ever so much like the pressure hull of a submarine doesn't it? Your tax dollars aren't going to the military of earth and haven't been going there for 70 years. We are paying for an secret civilization and have been paying for this civilization for the last 50 years or more. That's why these politicians are all crazy nut cases, they are all people whom have been chosen to fill roles to keep and illusion in place and to keep strip mining the people of money and resources.

Could be, but I think the cigar shape might possibly be a better alternative to a very large diameter saucer: you'll need less material for the MAGVID coils if they only wrap around your cigar craft, but you need to feed more power into those coils to make sure the bubble (= the two hemispheres of the BTV) will envelop the whole craft.

And I'm not sure if the hull can be metallic.
 

Gambeir

Celestial
Could be, but I think the cigar shape might possibly be a better alternative to a very large diameter saucer: you'll need less material for the MAGVID coils if they only wrap around your cigar craft, but you need to feed more power into those coils to make sure the bubble (= the two hemispheres of the BTV) will envelop the whole craft.

And I'm not sure if the hull can be metallic.

I was thinking of the undersea 2 miles across wandering dome that was found on google earth a while back. It's like the Ancient Alien Series, which though wonderful as it is, still is doing double duty: They tell you things, that is they tell the aware things, and I'm not sure why this is so but they do.

A submarine is a space ship already, and quite honestly we really don't know what space actually is, we only have the officially approved version of what it is. You notice that during the last decade or so they have begun referring to space as a medium, which makes sense but is there more to it?

Plasma are highly electrically conductive and so a magnetic field can lock the plasma to a magnetic field line, and if the magnetic pressure is greater than the plasmas', then the plasma is structured. Ergo, the glowing ball plasmoids seen and recorded can be explained by theory, but if one applies that explanation to explain these plasmoids in the attached video, then that raises some issues ,such as how does this happen without a machine being present to create the magnetic field in the first place? This 2012 video of the plasmoids spontaneously forming out of thin air in Cork Ireland is what I'm talking about.

I know that DARPA says they have succeeded in creating and sustaining open air plasmoids. I don't know exactly what we are seeing here but if these are demonstrations of open air plasmoids being demonstrated to frighten the natives than I think that these are being formed by different means, but are nevertheless still guided and controlled: They are weapons then, and probably these videos are masked warning to the other global gansters that they too have the latest weapons.

So the idea here is that possibly there's an explanation where the control over the ionized air/plasma exists and so the hull material may not be critical, or am I missing something?



So a plasma corona can be made to surround the machine, to encase it, to form a bubble, and which is pressurized (250K atmospheres sounds about right :) ~ joking~ ) which thus enables the machine to function without concern to the surrounding water pressures, allowing it to operate in the depths of the oceans equally as it can in the air and I'm assuming space at this point, but will have to think about it for a while.

From Wikipedia:
"The coronal and solar wind plasmas are highly electrically conductive, meaning the magnetic field lines and the plasma flows are effectively "frozen" together and the magnetic field cannot diffuse through the plasma on time scales of interest. In the solar corona, the magnetic pressure greatly exceeds the plasma pressure and thus the plasma is primarily structured and confined by the magnetic field."

Interplanetary magnetic field - Wikipedia
 
Last edited:
... Plasma are highly electrically conductive and so a magnetic field can lock the plasma to a magnetic field line, and if the magnetic pressure is greater than the plasmas', then the plasma is structured. Ergo, the glowing ball plasmoids seen and recorded can be explained by theory, but if one applies that explanation to explain these plasmoids in the attached video, then that raises some issues ,such as how does this happen without a machine being present to create the magnetic field in the first place? This 2012 video of the plasmoids spontaneously forming out of thin air in Cork Ireland is what I'm talking about.

I know that DARPA says they have succeeded in creating and sustaining open air plasmoids. I don't know exactly what we are seeing here but if these are demonstrations of open air plasmoids being demonstrated to frighten the natives than I think that these are being formed by different means, but are nevertheless still guided and controlled: They are weapons then, and probably these videos are masked warning to the other global gansters that they too have the latest weapons.

Referring to my post about the Repulsin, that the repulsin starts with air, but eventually forms a plasmoid/BTV by the action of the moving charged molecules generating magnetic fields: an axial magnetic field by traveling from the center out towards the rim, and a radial magnetic field by traveling from the rim back to the center. At a certain energy level, the system becomes self-sustaining and the electric motor driving the rilled diaphragms can be turned off.
Now, if there's a way to create a self-sustaning plasmoid/BTV without electronic or mechanical (i.e. Repulsin) means, this could explain your plasmoids and ball lightning too, I presume.

So the idea here is that possibly there's an explanation where the control over the ionized air/plasma exists and so the hull material may not be critical, or am I missing something?

I was thinking about eddy currents induced in any metals (e.g. a metallic hull) by the MAGVID's rotating virtual bar magnet. You'll lose energy producing them. Tests will tell.
 

spacecase0

earth human
I was thinking about eddy currents induced in any metals (e.g. a metallic hull) by the MAGVID's rotating virtual bar magnet. You'll lose energy producing them. Tests will tell.
if you have a steel hull, it will help the effect because of the steel magnifying the effect of the coils (like any transformer core). and if you make the hull parts electrically connected, it will get induction heating, but if you laminate it like you do in a transformer core, or just insulate panels from each other, you will not get to much heating.
once you get past the magnetic saturation point, or spin the field to fast, the steel is not going to help you at all.
wilbert smith said the part of the wrecked craft that he knew of was made out of a magnesium ferrite, not quite sure what that means though (replace the iron with magnesium ? or add magnesium to ferrite ?)
----------------------------
so, I tested the MAGVID idea slightly better than last time, only had rare earth magnets, and at that they were not sticking out past the coils either...
need to wind an electromagnet for the center coil, but have not made it to a hardware store yet.
either way, I am running somewhere less than 100W, 40KHZ, ~19inch dia., ~11 tall
started to smell ozone after it ran about 30 seconds. and it was not coming form the power supply, amplifiers, or any other of the electronics. can't run it at high power to long or my amplifier heats up.
so it does seem to do something, maybe...
it did not mess with a watch ticking off time (checked to 0.1 seconds after 5 min. run time)
does not mess with the binding strength meter at all
should be pretty easy for me to double my power in to it, will try to get to that today.
 
if you have a steel hull, it will help the effect because of the steel magnifying the effect of the coils (like any transformer core). and if you make the hull parts electrically connected, it will get induction heating, but if you laminate it like you do in a transformer core, or just insulate panels from each other, you will not get to much heating.
once you get past the magnetic saturation point, or spin the field to fast, the steel is not going to help you at all.
wilbert smith said the part of the wrecked craft that he knew of was made out of a magnesium ferrite, not quite sure what that means though (replace the iron with magnesium ? or add magnesium to ferrite ?)
----------------------------
so, I tested the MAGVID idea slightly better than last time, only had rare earth magnets, and at that they were not sticking out past the coils either...
need to wind an electromagnet for the center coil, but have not made it to a hardware store yet.
either way, I am running somewhere less than 100W, 40KHZ, ~19inch dia., ~11 tall
started to smell ozone after it ran about 30 seconds. and it was not coming form the power supply, amplifiers, or any other of the electronics. can't run it at high power to long or my amplifier heats up.
so it does seem to do something, maybe...
it did not mess with a watch ticking off time (checked to 0.1 seconds after 5 min. run time)
does not mess with the binding strength meter at all
should be pretty easy for me to double my power in to it, will try to get to that today.

Ozone?!!! Wow! That is a very significant result!!! It indicates ionization!!!!!!!!!!!

You should get/build a radiation meter to be on the safe side.
Electrons that change course forcefully will emit X-rays. Be careful.
Maybe DIY with a web camera.
 

spacecase0

earth human
I have a Geiger Counter, not sure how well it will do with x rays, never tested it before with x rays
charging its battery now.
I have an ion chamber detector, but not really sure where it is, will go looking, but might not even be at home, and poisonous spiders are at the other location (found a very bad one there today) and have not gassed it yet. (likely will not get to any store for the next week or so)
so not going to look in there till that is done.
I do have a modified camcorder that will selectively let me take all the filters off (infrared and UV, set up for ghost hunting), guess I should go try that first as I know where it is and is likely has enough of a charge
 

spacecase0

earth human
nothing on Geiger Counter, nothing on the camera.
will look for the ion chamber counter (the only one I would expect to work anyway)
 

Gambeir

Celestial
Referring to my post about the Repulsin, that the repulsin starts with air, but eventually forms a plasmoid/BTV by the action of the moving charged molecules generating magnetic fields: an axial magnetic field by traveling from the center out towards the rim, and a radial magnetic field by traveling from the rim back to the center. At a certain energy level, the system becomes self-sustaining and the electric motor driving the rilled diaphragms can be turned off.
Now, if there's a way to create a self-sustaning plasmoid/BTV without electronic or mechanical (i.e. Repulsin) means, this could explain your plasmoids and ball lightning too, I presume.



I was thinking about eddy currents induced in any metals (e.g. a metallic hull) by the MAGVID's rotating virtual bar magnet. You'll lose energy producing them. Tests will tell.

Gonna reply about 6 hours ago but just could not find the energy and to had to take a power nap~ snort~

Yes I understand the problem but there is probably a work round considering the relative reactions of metals to moving magnetic fields: Note the word moving, because it's possible the reaction of specific metals may be exploited. We have all seen a magnet dropped through a copper tube and slowed due to so~called Eddy Currents, but certain metals, the AG (Antigravity Metals) react strongly to any moving magnetic field (falling magnet for example) and for this reason make good demonstration metals to show the braking effect of eddy currents, but the force they induce, the magnetic pressure isn't proportional. It increases with the speed of the magnetic fields movement to repel the field away from itself.

Also, a probably really important insight was observed by Nivek about this phenomena, and that is to release the eddy currents is to break the circuit, which he suggested was possible by cutting holes or slices, as we already know that slicing a copper tube lengthwise will break this circuit and no eddy currents will be formed and the magnet will simply drop through any sliced tube as though it were a stone.

So now we have two results to work from and we know that aluminum, copper, and bismuth all have a disproportional repelling force relative to a moving magnetic field. As the speed of the magnetic field passing over the surface induces a disproportional magnetic repulsion (pressure). They are not ferromagnetic metals, but they do act well as conductors and react strongly to repel away from any magnetic field which is moving and in the case of the MAGVID this may be significant: Not sure, just suggesting.

We may be looking at a design issue. That is, one of breaking the eddy current inducing circuit, and or exploiting the reactive results which these metals and since developed alloys hold in repelling away from a moving magnetic field. That is to say; push away from the body of the vehicle as the speed or cycling and relative magnetic pressure increases.

I read the post you have made but I don't think I've quite yet put it together as well as you have: That is, all the relative spinning reactions and counter reactions, and which is more deeply explained in the area surrounding your analysis of the Repulsin. This is now a bit more clear in my minds eye. Slowly I turn...round and round.

The Repulsin, once better comprehended, does seem to now offer a basis for a general "Re~thunk" of the existing paradigm of aviation dominating war planning and does offer a number of avenues for thinking that Foo Figherts might have lead to a more advanced machine which employed the MAGVID.


I presently understand/see the developed outcome of the MAGVID as an artificial plasmoid. I mean this is what it seems to resemble, seems to be trying to accomplish, so it's like an evolutionary next step. A plasmoid, which essentially describes foo fighters, is a plasma ball with central hollow tube running through the center as can be seen below.

giantstructu.jpg

"Researchers at the U.S. Department of Energy's Princeton Plasma Physics Laboratory (PPPL) have for the first time simulated the formation of structures called "plasmoids" during Coaxial Helicity Injection (CHI)."

Read more at: https://phys.org/news/2015-06-giant-plasmoids-future-tokamaks.html#jCp
https://phys.org/news/2015-06-giant-plasmoids-future-tokamaks.html

Now plasmoids have been invaders from space for a long time. Typically I guess they like to blow up and make loud noises, and since the 1940's there has been increasing incursions of bolides and aerial bombardment from space along with a noticeable and recorded increase in noctilucent clouds, or night-shining clouds. So we've had people examining these issues for a while now, and it's likely that may foo fighers were actually invaders from space and natural forming plasmoids.

So the idea here they knew there was an ongoing environmental changes and some of the first of these Earth Changes were recognized by the reporting of so called Foo Fighters during the last Global War. Obvious now, but no so much during war time, but afterwards it was understood that environmental changes were coming from changes in space, and that its was something outside of the earth which was affecting earth.

Plasmoids seem to have invaded during wartime in numbers, and not previously noticed possibly because of the environment of war had significantly altered to Air Power Domination, and so these mysterious objects were routinely observed, and even fired on by bomber crews of all forces with no evident effect. These became labeled as Foo Fighters to calm the aircrews whom evidently routinely encountered them. It is very unlikely that plasmoids were harmless and presented no threat as the crews were told, but there was also no possible way to deal with them as they might potentially move at impossible speeds without warning, and or explode without cause, or even to decide to suddenly follow a carbon track from a bombers exhaust trail and instantly vaporize the whole thing, probably in the space between the blink of an eye, and who knows what else?

That who knows what else is probably archived somewhere's deep, deep, deep and so there was a drive to figure this all out.
 
I presently understand/see the developed outcome of the MAGVID as an artificial plasmoid. I mean this is what it seems to resemble, seems to be trying to accomplish, so it's like an evolutionary next step. A plasmoid, which essentially describes foo fighters, is a plasma ball with central hollow tube running through the center as can be seen below.

giantstructu.jpg

"Researchers at the U.S. Department of Energy's Princeton Plasma Physics Laboratory (PPPL) have for the first time simulated the formation of structures called "plasmoids" during Coaxial Helicity Injection (CHI)."

Read more at: https://phys.org/news/2015-06-giant-plasmoids-future-tokamaks.html#jCp
https://phys.org/news/2015-06-giant-plasmoids-future-tokamaks.html

Now plasmoids have been invaders from space for a long time. Typically I guess they like to blow up and make loud noises, and since the 1940's there has been increasing incursions of bolides and aerial bombardment from space along with a noticeable and recorded increase in noctilucent clouds, or night-shining clouds. So we've had people examining these issues for a while now, and it's likely that may foo fighers were actually invaders from space and natural forming plasmoids.

It is my opinion that many of those plasmoids/orbs might be living entities. Just look at the footage from the space shuttle missions where a number of spherical object move about outside the shuttle. Literal swarms of them, and they're translucent too.
Maybe it's hard for people to accept that life could exist in the earth's upper atmosphere, because most UFO buffs refer to them as space craft. David Wilcock has written about these life forms, e.g. in Divine Cosmos. There's also an interesting discussion about so-called vacuum domains and conciousness units in some of his other free online books. Actually, it's these early texts that got me listening to the guy, although this Corey Goode thing is a little depressing...
 
spacecase0, could you take photographs of your setup and post them? Very Curious!
Also, could you describe the components you used, very briefly if you don't have enough time?

Would love to know!
 

Gambeir

Celestial
It is my opinion that many of those plasmoids/orbs might be living entities. Just look at the footage from the space shuttle missions where a number of spherical object move about outside the shuttle. Literal swarms of them, and they're translucent too.
Maybe it's hard for people to accept that life could exist in the earth's upper atmosphere, because most UFO buffs refer to them as space craft. David Wilcock has written about these life forms, e.g. in Divine Cosmos. There's also an interesting discussion about so-called vacuum domains and conciousness units in some of his other free online books. Actually, it's these early texts that got me listening to the guy, although this Corey Goode thing is a little depressing...

No disagreement from me on your view point. I think we've got two types of critters running round. We have the inanimate one's that come from our own Star, which are the actual plasmoids, and then we have these space critters that Trevor Constable talked about.

This is why I mentioned the change in the descriptors of space being a medium; we really only have the officially approved version of space and this appears to be slightly and slowly changing to include space now being described as a medium. What is a medium? Is it a fluid, is it fluid like, what exactly is this medium? Just judging by the record shown here in this video of STS~75 it looks like we are smaller than single cell critters and our entire Universe is inside a petri dish.

NASA UFO STS-75 The Tether Incident
 

spacecase0

earth human
I don't really have a way to post images to the web, every website I try does not work with my browser.
I could try harder though (it was so easy when I ran a web server)

I have 2 of these
https://www.amazon.com/Longruner-Arbitrary-Frequency-FY2300-Generator/dp/B01FF0SQT6/

the amplifier appears to be on an uncooperative website ( droking.com ), so no link.
I have 2 of these (they are sold as regular audio amplifiers, no case, just a circuit board)
50W peak for each of the 2 channels, 10 to 28V in, 14Hz to 100KHz, 4-8 ohms,
uses a TPA3116 chip (1.2MHz switching frequency) and has a flat output to 50KHz
I power them with 24V (some old 24V 15A switching supply)

coils are 21 turns of what seems to be 19 gauge magnet wire, taped together (no frame of any sort)
they are on a glass table that has an aluminum frame (from IKEA)

my oscilloscope is LeCroy WaveAce 101

magnets for the center field are 1/2 inch dia, 32 of them in the stack, total length is almost 3.5 inches, so, yes, shorter than the coils.

camera is an no longer sold 1080P HD model from Cleveland Paranormal Supply Co - Ghost Hunting Store

Geiger Counter is an older version of this
Electronic Goldmine - C7071 Display Geiger Counter Kit
but has a metal tube, the metal one in this picture
Electronic Goldmine - Dual Tube Geiger Counter Kit

I have lots of other hardware that you would see in a picture, but they are not involved with this test.
 
I don't really have a way to post images to the web, every website I try does not work with my browser.
I could try harder though (it was so easy when I ran a web server)

I have 2 of these
https://www.amazon.com/Longruner-Arbitrary-Frequency-FY2300-Generator/dp/B01FF0SQT6/

So one of these can generate a quadrature signal, e.g. CH1=sine, CH2=cosine?

the amplifier appears to be on an uncooperative website ( droking.com ), so no link.
I have 2 of these (they are sold as regular audio amplifiers, no case, just a circuit board)
50W peak for each of the 2 channels, 10 to 28V in, 14Hz to 100KHz, 4-8 ohms,
uses a TPA3116 chip (1.2MHz switching frequency) and has a flat output to 50KHz
I power them with 24V (some old 24V 15A switching supply)

I've looked into using high-speed power OP-amps (not IC's). They're pricey, though. Will such beasts work? My analog skills suck.
 
Top